spaceclaim engineer 2015 Год/Дата Выпуска: 2014 Версия: 2015.0 Разработчик: SpaceClaim Разрядность: 32bit, 64bit Язык интерфейса: Мультиязычный (русский отсутствует) Таблэтка: Присутствует Системные требования: Operating Systems: Microsoft® Windows 7 32-bit and 64-bit Microsoft® Windows 8 64-bit SpaceClaim is not supported on virtual platforms (See note below). Intel-based Apple hardware running native Windows using Boot Camp is not supported. Video Card: Requires Full DirectX® 9c, Shader Model 3.0 hardware support, 256 MB of graphics memory or higher, 32 bits per pixel, 1024x768 minimum resolution. The following commonly used video cards support the above requirements1 : Radeon®: ATI® Radeon R300, R420, R520, R600, or R700 series. Radeon 9x00 cards (9700, 9800, …) or newer NVIDIA®: NVIDIA GeForce® FX, 6, 7, or 8 series. NVIDIA FX5200s or newer AMD™: AMD FireGL™ T2-128 or higher (including the ‘Mobility’ series for laptops) CPU: Pentium® 4 2.0 GHZ or Athlon® 2000+ or faster, 32-bit (x86) or 64-bit (x64) processor RAM: Minimum: 512MB RAM (32-bit), 1Gb RAM (64-bit) Recommended: 2GB RAM or higher Other: CD drive (only for CD installation) 2 Button Mouse with Wheel 3D Mouse (3Dconnexion - Optional) Multi-touch: Multi-touch now works on all Windows 7 and 8 devices via the native pen-and-touch interface. Note regarding Microsoft® .NET Framework 4.0: SpaceClaim requires .NET 4.0, and an installer for .NET 4.0 is included within the SpaceClaim installer. It is possible in some cases that a corrupt version of .NET will be detected as the correct version by the SpaceClaim installer. If this happens, SpaceClaim will be installed, but will not run properly. To remedy this, please manually install .NET 4.0 using Microsoft's web site, Microsoft Update or Windows Update. On some occasions, this may involve cleaning the .NET installation by uninstalling any .NET components and re-installing them all. More details can be found on Microsoft's web site here. Once the .NET 4.0 installation is successful, the SpaceClaim installation should proceed normally. Note on virtual platforms: Users report successfully operating SpaceClaim on VMware Workstation 7.x and Player 3.x. Описание: Программа для создания и редактирования твердотельных 3D-моделей, в первую очередь адресованная инженерам, которым необходимо внести свой вклад в разработку изделия, но которые в настоящее время не используют ни одну из «первичных» MCAD-систем. Программа может работать с большинством форматов 3D MCAD-систем, а также хранить данные в собственном, полностью открытом формате, основанном на технологии XML. Поддерживаемые форматы: ACIS, STEP, IGES, ECAD, Rhinoceros, CGR, DWG, DXF, STL, OBJ, XAML, VRML и другие. Доп. информация: Программа устанавливается ,но сваливается в режим вьювера. Надеюсь кто нибудь сможет победить ее и подскажет как это сделать.
Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете голосовать в опросах Вы не можете прикреплять файлы к сообщениям Вы можете скачивать файлы